Komatsu code e03. Komatsu Fault Codes 2019-05-22

Komatsu code e03 Rating: 6,8/10 1375 reviews

Komatsu Error Codes list

komatsu code e03

Thanks for any input in advance. E15, engine sensor water temperature, fuel pressure, oil pressure failure. The shelf life of the hose should not exceed 2 years. E225, the rear pump pressure sensor circuit is abnormal. There is a short circuit in the system sensor wiring; possibly from a staple placed through the wire, or damage to the wire causing both conductors to touch. Komatsu forklifts are designed with the same heavy equipment expertise that give our customers greater value through lower costs of operation daily.

Next

E03 Fault Code

komatsu code e03

E213, Swing parking brake solenoid valve circuit breaker. E227, the engine speed sensor is abnormal. The following are some of the most common error codes, what they mean, and what you need to do to address it. Page 20-459 will give you the information you need to troubleshoot this issue. E315, the battery relay output circuit. Service code need to switch operation code: E101, fault history exception.

Next

code E03. Discussion about troubleshooting Komatsu

komatsu code e03

Among them, electric excavators are mainly used in high altitude anoxic and underground mines and other inflammable and explosive places. When carrying out pushing operations, set the bottom of the bucket parallel to the ground surface. Using screws 4 and 5 , install a new slow blow fuse together with electric wiring 7 and 8 to the slow blow fuse box, then close covers 1 , 2 , and 3. E231, activation rotary solenoid circuit. Thank y'all fro the replies. E224, before the pump pressure sensor circuit is abnormal. Service code the need for switching operation Code: E101, fault history exception.

Next

[Troubleshooting] Komatsu excavator fault code fault code

komatsu code e03

E203, short circuit of the rotary parking brake solenoid valve circuit. Always measure on level ground. Look up page 20-438 in your manual to find out what to do. Keep the right brake pedal depressed. We have roughly 30 peices of machinery that is komatsu. Be sure no one is on or near machine.

Next

code E03. Discussion about troubleshooting Komatsu

komatsu code e03

E112, wiper motor drive forward system shorted new. E102, the clock data is abnormal. E226, pressure sensor circuit power anomalies. E313, Automatic for the fat controller failure optional E315, the battery relay output short circuit E316, governor motor disorders. E213, Swing parking brake solenoid valve circuit breaker. E216, walking speed converter solenoid circuit.

Next

KOMATSU Fault Codes DTC

komatsu code e03

E207, fast mode solenoid valve circuit short circuit. E103, buzzer output short circuit, buzzer driving harness contact with the 24V power cable. For pit excavation operations, do not use a wheel loader. E10, engine controller power failure, the engine control drive system circuit fault this engine is stopped. E112, wiper motor drive forward system shorted new.

Next

Komatsu PC 360 lc troulbe code L03

komatsu code e03

E03, rotary parking brake system. Replace the accumulator every 4000 hours or every 2 years. E308, fuel dial input is abnormal. The system sensor is faulty. It is dangerous to jack up the machine without taking due care. I hope that the excavator operation driver can know the meaning of these fault codes, know the problem through the code prompted by the excavator display, and stop the repair in time to prevent the accident.

Next

KOMATSU Fault Codes DTC

komatsu code e03

Check the oil for presence of water before and after starting the engine. E226, the pressure sensor circuit power supply is abnormal. Even in the areas where freezing is not an issue, the use of antifreeze coolant is essential. E03, Swing parking brake system. Armrest adjustment lever Pull this lever 11 to adjust the height of the armrest within range a of 26 mm 1. When closing the door after getting off the machine, pull knob 3 to release the catch.

Next

KOMATSU Fault Codes DTC

komatsu code e03

After greasing, wipe off any old grease that was pushed out. E206, walking speed converter solenoid circuit. The reason the swing brake has this switch is because in the past the timer for the function would go out and leave the swing brake on all the time. Run the engine for a short time at idling, then check that the oil is at the specified level. Method of displaying failure code 1.

Next

Komatsu Error Codes list

komatsu code e03

E03, Swing parking brake system. Operate the lift arm control lever to lower the bucket to the ground. E313, Automatic for the fat controller failure optional. The new load is added to the load existing before operations were stopped. E231, activation rotary solenoid circuit. The air flow is shown in air flow bar A on the air conditioner monitor. E318, the governor motor circuit is short circuited.

Next